®
OWNER’S MANUAL
Outdoor LP Gas Light
Model No. GTL7179SP
WARNING
FOR YOUR SAFETY:
Table of Contents
For Outdoor Use Only
(outside any enclosure)
Dangers and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2
Exploded View & Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Assembly Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
installing LP Gas Tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operating Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Checking for Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Turning Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Inspecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Product Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
WARNING
FOR YOUR SAFETY:
If you smell gas -
1. Shut off gas to appliance.
2. Extinguish any open flame.
3. If odor continues, immediately call your
gas supplier.
WARNING
FOR YOUR SAFETY:
If the information in this manual is not followed
exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
Improper installation, adjustment, alteration,
service or maintenance can cause injury or
property damage.
The use and installation of this product must conform to local codes. In absence of local codes,
use the latest edition of the National Fuel Gas Code, ANSI Z223.1/NFPA 54, CAN/CGA-B149.1,
Natural Gas and Propane Installation Code.
Read the installation, operation, and maintenance
instructions thoroughly before installing or
servicing this equipment.
For installation in Canada - these instructions, while generally acceptable do not necessarily
comply with the Canadian installation codes, particularly with piping above and below ground.
In Canada the installation of this appliance must comply with local codes and/or standard
CAN/CGA B149.1 (installation code for propane burning appliances and equipment).
Save these instructions for future reference.
If you are assembling this unit for someone else,
give this manual to him or her to read and save
for future reference.
California Proposition 65: Chemicals known to the State of California to cause cancer, birth
defects, or other reproductive harm are created by the combustion of propane.
Manufactured in China for:
Blue Rhino Global Sourcing, LLC
Winston-Salem, NC USA
© 2007 Blue Rhino Global Sourcing, LLC. All Rights Reserved
Endless Summer® is a Registered Trademark of Blue Rhino Global Sourcing, LLC. All Rights Reserved
GTL7179SP-OM-100 E
page no.
3
Contact 1.800.762.1142 for assistance. Do not return to place of purchase.
Parts List
Exploded View
1
1
2
3
4
5
6
7
8
9
Finial
Top Cap
2
Insect Guard
Top Cap Assembly
Pilot Shield
3
4
5
6
Bottom Lid Assembly
Engine Assembly
Control Knob
Top Pole
10 Bottom Pole
11 Shroud Cover
12 Regulator/Hose Assembly
13 Shroud
8
7
14 Base
15 Weight Plate
9
10
11
12
13
14
15
Hardware
Tools Required for Assembly (Included)
#2 Phillips Head Screwdriver
3/16 in. x 1/2 in. Black Nickel Plated Phillips
Truss Head
Screw
4 pcs
A
5/32 in. x 1 1/5 in. Black Nickel Plated
1/4 in. x 1 4/5 in. Nickel Plated Hex Head
1/4 in. Nickel Plated
Bolt
3 pcs
4 pcs
8 pcs
4 pcs
4 pcs
B
C
D
E
Bolt
Nut
7/16” Wrench
ø7 Nickel Plated
Washer
ø6 Nickel Plated
Lock Washer
F
®
Outdoor LP Gas Light Model No. GTL7179SP
Assembly Instructions
For Easiest Assembly:
DO NOT RETURN PRODUCT TO STORE.
• To avoid losing any small components or hardware, assemble your product on a hard level
surface that does not have cracks or openings.
For assistance call 1.800.762.1142 toll free. Please have your owner’s manual and serial
number available for reference.
Attach Shroud
Attach Weight Plate
1
2
x 4
C
x 4
D
x 4
E
x 4
F
x 4
D
Insert Regulator/Hose Assembly
Attach Engine Assembly
5
6
Attach Regulator/Hose Assembly
page no.
5
Contact 1.800.762.1142 for assistance. Do not return to place of purchase.
• Clear an area large enough to layout all components and hardware.
• Follow all steps in order to properly assemble your product.
• When applicable, tighten all hardware connections by hand first. Once the step is completed,
go back and fully tighten all hardware.
Attach Bottom Pole Assembly
Attach Top Pole
3
4
x 4
A
Attach Top Assembly
7
x 3
B
®
Outdoor LP Gas Light Model No. GTL7179SP
Installing LP Gas Tank
Operating Instructions
Checking for Leaks
To operate you will need (1) 14.1 oz or (1) 16.4 oz LP gas tank.
LP Gas
Connection
Burner
venturi
WARNING: Before using this Outdoor Light,
make sure you have read, understand and
are following all information provided in the
Dangers and Warnings presented on page 2.
Failure to follow those instructions can cause
death, serious injury or property damage.
Insert LP Gas Tank
Place precision filled LP gas tank upright into hole in outdoor gas light body so it is arranged
for vapor withdrawal.
Burner Connections
Make sure the regulator valve and hose
connections are securely fastened to the burner
and the tank.
LP Gas Valve
with Orifice
Burner
If your unit was assembled for you, visually check
the connection between the burner pipe and orifice.
Make sure the burner pipe fits over the orifice.
X
WARNING: Failure to inspect this connection
or follow these instructions could cause a fire
or an explosion which can cause death, serious
bodily injury, or damage to property.
Please refer to diagram for proper installation.
If the burner pipe does not rest flush to the orifice,
please contact 1.800.762.1142 for assistance.
Tank/Gas Line Connection
Connect LP Gas Tank
Make 2-3 oz. of leak solution by mixing one part
liquid dishwashing soap with three parts water.
WARNING: Only cylinders marked “propane” may be used.
Note: Some 14.1 oz or 16.4 oz LP gas tanks may form frost when near empty.
Make sure control knob is OFF.
Attach the LP gas tank.
Line up threads on LP gas tank with those on regulator, insert and rotate LP gas tank
clockwise until they fit snugly together. HAND TIGHTEN ONLY. Be careful not to cross threads
when screwing in LP gas tank.
Spoon leak check solution at all “x” locations
If no bubbles appear after one minute turn control
knob to “OFF”, wipe away solution and proceed.
Control Knob
Lighting
1. Make sure there are no obstructions of airflow to
the gas unit. Spiders and insects can nest within
and clog the burner / venturi tube at the orifice.
A clogged burner tube can lead to a fire beneath
the appliance.
2. Control knob must be in the “OFF” position.
3. Attach the LP gas tank.
4. Push in control knob and rotate to “ON” position.
This will activate the built-in ignitor and light
the burner. If necessary, keep depressing and
rotating knob until burner lights.
5. If ignition does not occur in 5 seconds, turn
burner control knob to “OFF”, wait 5 minutes,
and repeat lighting procedure.
Disconnect LP Gas Tank
Rotate LP gas tank counterclockwise until the LP gas tank comes off.
6. Once the burner is lit, hold control knob in for
30 seconds.
7. If burner does not stay lit, turn to “OFF”
position and wait 5 minutes and repeat lighting
procedure.
4 in.
10 cm.
8. After lighting, observe the burner flame and
flame height matches illustration.
3 in.
7.5 cm.
CAUTION: If burner flame goes out during
operation, immediately turn the gas “OFF” and
open top cap to let the gas clear for about 5
minutes before re-lighting.
2 in.
5 cm.
1 in.
2.5 cm.
0 in.
0 cm.
Turning Off
1. Remove the LP gas tank.
Burner proper flame height.
2. Once the flame goes out, turn the control knob
clockwise to “OFF” position.
3. Properly store LP gas tank.
Note: May take up to 5 minutes for flame to
extinguish.
page no.
7
Contact 1.800.762.1142 for assistance. Do not return to place of purchase.
Cleaning and Care
Limited Warranty
Blue Rhino Global Sourcing, LLC (“Vendor”) warrants to the original retail purchaser of this
product, and to no other person, that if this product is assembled and operated in accordance
with the printed instructions accompanying it, then for a period of one (1) year from the date
of purchase, all parts in such product shall be free from defects in material and workmanship.
Vendor may require reasonable proof of your date of purchase. Therefore, you should retain
your sales slip or invoice. This Limited Warranty shall be limited to the repair or replacement of
parts, which prove defective under normal use and service and which Vendor shall determine
in its reasonable discretion upon examination to be defective. Before returning any parts, you
should contact Vendor’s Customer Service Department using the contact information listed
below. If Vendor confirms, after examination, a defect covered by this Limited Warranty in any
returned part, and if Vendor approves the claim, Vendor will replace such defective part without
charge. If you return defective parts, transportation charges must be prepaid by you. Vendor will
return replacement parts to the original retail purchaser, freight or postage prepaid.
Inspecting
This outdoor light should be inspected on a regular basis to ensure product safety and longer
product life.
WARNING: Do NOT attempt to inspect this outdoor light until the fire is COMPLETELY
out.
1. Check venturi to make sure it is clear and free of spider nests.
2. Check all gas connections for leaks.
3. Check ignition system to insure proper sparking.
4. Check components for any signs of damage or rust.
5. If damage to any component is detected, do NOT operate until repairs are executed.
This Limited Warranty does not cover any failures or operating difficulties due to accident,
abuse, misuse, alteration, misapplication, improper installation or improper maintenance or
service by you or any third party, or failure to perform normal and routine maintenance on
the product as set out in this owner’s manual. In addition, the Limited Warranty does not cover
damage to the finish, such as scratches, dents, discoloration, rust or other weather damage,
after purchase.
Cleaning
This outdoor light should be cleaned on a regular basis to promote safer experiences and
longer product life.
This Limited Warranty is in lieu of all other express warranties. Vendor disclaims all warranties
for products that are purchased from sellers other than authorized retailers or distributors,
including the warranty of merchantability or the warranty of fitness for a particular purpose.
VENDOR ALSO DISCLAIMS AND ANY ALL IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. VENDOR SHALL NO LIABILITY TO PURCHASER OR ANY THIRD PARTY FOR ANY
SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. Vendor further
disclaims any implied or express warranty of, and assumes no responsibility for, defects in
workmanship caused by third parties.
Note: After repeated use, a slight discoloration of the finishes may occur.
WARNING: Do NOT attempt to clean this outdoor light unless the fire is COMPLETELY
out and unit is cool to the touch.
WARNING: Do NOT use oven cleaner or abrasive cleaners as they will damage this
product.
1. Wipe exterior surfaces with a mild dishwashing detergent or baking soda.
2. Rinse clean with water.
This Limited Warranty gives the purchaser specific legal rights; a purchaser may have other
rights depending upon where he or she lives. Some jurisdictions do not allow the exclusion or
limitation of special, incidental or consequential damages, or limitations on how long a warranty
lasts, so the above exclusion and limitations may not apply to everyone.
3. Glass can be cleaned with glass cleaner.
Storage
Vendor does not authorize any person or company to assume for it any other obligation or
liability in connection with the sale, installation, use, removal, return, or replacement of its
equipment, and no such representations are binding on Vendor.
WARNING: Do NOT move or store this outdoor light unless the fire is COMPLETELY
out and is cool to the touch.
Blue Rhino Global Sourcing, LLC
Winston-Salem, North Carolina USA
(800) 762-1142
1. Remove the LP gas tank.
2. Once the flame goes out, turn the control knob clockwise to the “OFF” position.
Note: May take up to 5 minutes for flame to extinguish.
3. Cover outdoor light with a durable vinyl cover designed to fit this unit.
4. Store in a cool and dry location away from children and pets.
Product Registration
call 1.800.762.1142.
®
Outdoor LP Gas Light Model No. GTL7179SP
Troubleshooting
Problem
Possible Cause
Prevention/Cure
Burner will not light using igniter
Electrode and burners are wet.
Wipe dry with cloth.
Electrode cracked or broken - sparks at crack.
Wire loose or disconnected.
Replace electrode.
Reconnect wire or replace electrode/wire assembly
Replace igniter wire/electrode assembly
Replace igniter
Wire is shorting (sparking) between igniter and electrode.
Bad igniter.
No gas flow.
Check if LP gas tank is empty. If LP gas tank is not empty, refer
to “Sudden drop in gas flow (reduced flame height). If empty,
replace.
Coupling nut and regulator not fully connected.
Turning the coupling nut about one-half to three quarters
additional turn until solid stop. Tighten by hand only-do not use
tools.
Obstruction of gas flow.
Clear burner tubes. Check for bent or kinked hose.
Reengage burner and valve.
Clean venturi.
Disengagement of burner to valve.
Spider webs or insect nest in venturi.
Burner ports clogged or blocked.
Out of gas.
Clean burner ports.
Sudden drop in gas flow or reduced flame height
Irregular flame pattern
Check for gas in the LP gas tank
Clean burner ports.
Burner ports are clogged or blocked.
Low on LP Gas
Flame blow out
Replace LP gas tank
Excess flow valve tripped
Refer to “Sudden drop in gas flow”
Flame seems to lose heat when burning in cold weather Ice has built up on the outside of the LP gas tank because the Turn OFF the control knob and the LP gas tank. Replace with a
- temperature below 50ºF
vaporization process is too slow.
spare LP gas tank and resume burning. Store a spare LP gas
tank in a well ventilated area away from children.
If problems can not be corrected by using these methods, please contact 1.800.762.1142 fo assistance.
|